Coating and Repair Epoxies
Stratmore manufactures a wide range of liquid epoxies for site, factory, workshop and home/business use. Epoxy crack injection, sealing, joint filling and repair systems to bond, repair and coat concrete, adhere steel into concrete, protect concrete against chemical attack, etc.
Product
EPAR 121B
EPAR 121B is a solvent-free liquid epoxy which has very good mechanical strength, good chemical resistance and excellent flexibility. EPAR 121B adheres very well to concrete, metal and asphalt and can be used for road or driveway repairs, coating metal surfaces, protecting concrete, etc.
What's it used for?
EPAR 121B has excellent compatibility with asphaltic surfaces. It may be used as a coating onto which grit or aggregate is bonded to form a skid resistant wearing course. EPAR 121B can be used to line steel substrates for repair or protection (for example, repairing steel gutters). EPAR 121B may be used as a chemically resistant coating for bitumen and concrete surfaces, against acids, oils, fats etc.
The combination of flexibility and strength make EPAR 121B suitable as a joint filler where a small amount of movement is expected, e.g., expansion joints in concrete slabs. Rubber crumb can be mixed into EPAR 121B to increase flexibility even more.
What can it be applied to?
EPAR 121B can be applied to asphaltic surfaces, concrete, steel and similar substrates. It is self-priming and does not require a prime coat (unless mixed with aggregate).
Limitations
Not suited to vertical application due to its self-levelling properties. For chemical bunding applications, testing of EPAR 121B using the proposed chemicals (and length of exposure) should be undertaken prior to application.
Product
EPAR 226
EPAR 226 is a low viscosity, unfilled epoxy with excellent mechanical properties. EPAR 226 may be used for a variety of applications as supplied or may be mixed with suitable aggregate to make epoxy mortars, grout or toppings.
EPAR 226 fully complies with the test requirements of AS/NZS 4020, Products for use in contact with potable water (standard hardener only).
What's it used for?
EPAR 226 is a versatile liquid epoxy system. It can be used for:
Grouting or bedding of machinery, base plates, crane rails, precast concrete units etc
General patching and repair of concrete when mixed with aggregate to form a mortar
Repair of cracks in concrete by injection or gravity feed
Crack injection of structural concrete – refer to EPAR 226XLV data sheet
New to old concrete tie coat.
EPAR 226 can also be used as a coating/sealer for concrete floors (by approved applicators only).
EPAR 226 is suitable for coating the inside of water retaining tanks or pipelines in contact with drinking water.
What can it be applied to?
EPAR 226 can be applied to a wide range of substrates including concrete, steel, timber, brick, etc.
For high strength concrete crack injection, use EPAR 226XLV.
When applied to surfaces in contact with potable water, EPAR 226 must be fully cured (5 to 7 days), then washed down with water and the washdown water discarded.
Limitations
Not suitable for application to plastic substrates.
When used as a floor coating, application must be by an experienced coatings applicator approved by Stratmore Construction Solutions.
EPAR 226 fully complies with the test requirements of AS/NZS 4020:2005 (contact with potable water) to cover a cold water application up to <40°C, at the recommended ‘total immersion’ exposure of ~30,000mm² per litre of water (standard hardener only). Refer to technical data sheet for application requirements for potable water applications.
Product
EPAR 733HV
EPAR 733HV is a high build, 100% solids, solvent-free epoxy system used to coat steel and concrete structures exposed to a wide range of chemicals. EPAR 733HV is applied in one to two coats to concrete and steel. It has excellent chemical resistance.
EPAR 733HV fully complies with the test requirements of AS/NZS 4020, Products for use in contact with Drinking Water (standard hardener only).
What's it used for?
Use EPAR 733HV to protect concrete and steel structures exposed to chemical immersion or contact, including concrete pipes and precast concrete used in sewerage systems. EPAR 733HV is also used to coat concrete or other surfaces for water retaining or reticulation in contact with drinking water.
Other uses are for lining vehicle inspection pits, manhole access points, bunds, etc.
What can it be applied to?
EPAR 733HV can be applied to clean, sound concrete or steel substrates. It is suitable for both horizontal and vertical applications.
Limitations
If this product is to be used as a floor coating, sealer, floor levelling and repair, etc it must be applied by a professional applicator only i.e. those that are professionally trained flooring applicators and are approved by Stratmore.
If the substrate coated with EPAR 733HV is exposed to chemicals listed as “Not Suitable” or “Suitable for Intermittent Contact only” according to the chemical resistance chart on the data sheet (or if the chemical is not listed), then the coating must be inspected for signs of damage due to chemical action.
Product
EPAR 122 COLD CURE
EPAR 122 COLD CURE is an unfilled, non-shrink solvent-free epoxy liquid that is primarily used as a cold-curing concrete crack and joint repair system. It may also be used as a cold-curing primer for concrete surfaces prior to the application of other epoxy systems.
Cures down to 0°C
What's it used for?
EPAR 122 COLD CURE is also used as a concrete crack and joint repair system in low temperature applications. Common applications are the repair of cracked and spalling concrete joints in freezers or other low temperature storage areas.
EPAR 122 COLD CURE can be used as a primer for EPAR liquid epoxies and mortars when used on rough, absorbent surfaces at low temperatures.
What can it be applied to?
EPAR 122 COLD CURE is suitable for application to concrete substrates.
Limitations
EPAR 122 COLD CURE will cure down to 0°C. Initial and final cure times will be increased at lower temperatures (compared to testing at 18°C). Ensure epoxy is cured prior to opening to traffic.
At very low temperatures, warm the substrate (with hot air). Warm the epoxy hardener and resin (stand in hot water) prior to mixing and application.
Product
EPAR 226XLV
EPAR 226XLV is a low viscosity, unfilled solvent-free epoxy with excellent mechanical properties.
What's it used for?
EPAR 226XLV is used as a crack injection epoxy for concrete repairs by injection or gravity feed. Due to its low viscosity, EPAR 226XLV will fill the pores and cavities within the concrete, restoring strength to the structure under repair.
What can it be applied to?
EPAR 226XLV is applied into concrete substrates under pressure or gravity feed.
Limitations
Not suitable for application to plastic substrates.
EPAR 226XLV is not potable water contact approved. For potable water contact applications, use EPAR 226.
Product
PLASTICAST LQB/LQG
PLASTICAST LQB is a two-part epoxy compound formulated specifically for use in bitumen and asphaltic surfaces. It is pigmented black. PLASTICAST LQB is internally flexibilised so as to allow differential movement without delamination, stress and cracking.
What's it used for?
PLASTICAST LQB/LQG is used to encapsulate road traffic light signal cable loops, saw cut joints, cracks and repairs, etc.
PLASTICAST LQG is typically used in concrete applications, with LQB used in asphaltic applications to more closely match the colour of the substrate.
PLASTICAST LQB/LQG has excellent (electrical) insulating properties.
What can it be applied to?
PLASTICAST LQB/LQG can be applied to asphaltic/bitumen and concrete substrates. It may also be applied to other substrates including concrete and steel (test for the intended application).
Product
EPAR S
EPAR S is a low viscosity, lightly filled, high strength epoxy grout. EPAR S has very good mechanical properties and chemical resistance.
Available in a standard grade or as a FAST-SET/COLD-CURING version.
What's it used for?
EPAR S is used for filling spalls, cracks and chips in concrete floors and for grouting holding down bolts or starter bars into concrete.
It is also used for grouting under machinery, bearing plates, crane rails etc and as high strength nosings for bridges and industrial floors.
EPAR S FAST SET/COLD CURE is used for applications down to 0°C.
What can it be applied to?
EPAR S is applied to concrete and steel (bonding steel into concrete or under steel base plates/crane rails).
EPAR S may be used to level uneven and spalled concrete substrates not subject to moisture penetration through the substrate.
Limitations
EPAR S can be used to level existing concrete substrates. When used as a coating in this type of application, only experienced floor coatings applicators are to apply.
Information presented on this website must be read in conjunction with the latest technical datasheet, product label and any other application data.
Click here to download technical data
Phone
0800 835 699
Wellington: 04 567 8436
or North Island region: Craig (027) 442 2942
Nelson: 03 546 5644
Jos Willems (Branch Manager)
or South Island region: Rob (027) 235 7447
Email: info@stratmore.co.nz
Physical
Head Office (Wellington)
185 Rata Street, Naenae
Lower Hutt 5011
Nelson Branch
11b Pascoe Street
Nelson 7011
Contact Us
Use of this website is subject to the conditions and details listed below under the drop down menus - Disclaimer and Privacy.
Disclaimer
This website provides brief product descriptions of our products. Information is included for illustrative purposes only. It is not a product application guide.
Do not use or specify our products without following the printed application guidelines on the current technical data sheets, product labels, material safety data sheets and any other supporting literature. We reserve the right to alter formulations without notice.
Properties as stated were determined under controlled laboratory conditions.
We give no guarantee of results of product use since conditions of use are beyond our control. Buyers and users are urged to make their own assessment of our products under their own conditions and for their own requirements.
If you are a customer, then any contract with you is in accordance with our latest terms and conditions, which are available on request or can be downloaded from this website. Where goods are acquired for business purposes, the Consumer Guarantees Act 1993 does not apply.
To the maximum extent permitted by law, we have no liability (whether statutory, in contract or negligence or otherwise) to buyers, users or specifiers of our products for any physical, direct or indirect damage, economic loss or any other loss or costs caused or contributed by us or any of our agents or employees in respect of any goods or services supplied. Also to the maximum extent permitted by law, all conditions and warranties expressed or implied by statute or common law, equity, trade custom or usage or otherwise howsoever are excluded. If, despite this, Stratmore Construction Solutions Limited is found to have any liability, then it is agreed that the liability is limited to the price of the relevant goods or services purchased.
Privacy
We take your rights, along with the privacy and confidentiality of your data, seriously. In accordance with the Privacy Act 2020 the information that you provide is the least amount of information that we require for engaging with you and allow us to provide you with the information requested from us. For any questions about the collection and use of your personal data, please get in touch on info@stratmore.co.nz